Horn Installation
Compressor
Compressor:MOUNTING
Determine a dry place to mount your compressor. If you have chosen to install in the engine compartment, you should mount it as close to the front as possible to allow for maximum flow of air around compressor and also to avoid heat from the exhaust.
Compressor:ELECTRICAL CONNECTION
The red wire of the compressor should be connected to (+) 12-volt power source.
Product Specifics
Brand: ECCPP
Manufacturer Part Number: ECC16730001PP
Type: Electric Air Horn Compressor Kit
Horn Type: High Pressure Air
Features: Quick Release
Fitment Type: Direct Replacement
Mounting Hardware Included: Yes
Quantity: 1
Custom Bundle: No
Modified Item: No
Kit or Single Part: Kit
Interchange Part Number: Air Compressor
Other Part Number: SUV Boat Motorcycle Truck Car Boat Horn Kit
Superseded Part Number: Air Horn Compressor Kit
Horn Volt: DC 12V
Color: Silver
Surface Finish: Chrome
Material: Metal
Weight: 4.3 lb
Package Size: 7.87"x6.69"x4.72"
Current: 20.0A
Air Horn 150psi Compressor 30A Fuse Kit 12V
12V Permanent Magnetic Motor
Maximum Working Pressure: 150 PSI
Duty Cycle: 25% @ 100 PSI
Amperage Draw: 20A
Flow Rate: 1.9CFM @ 0 PSI
Oil-less Design
Moisture and Dust Resistant
Anodized Aluminum Alloy Cylinder
Automatic Reset Thermal Overload Protector
Mounting Plates with Vibration Isolators
1/4??NPT Stainless Steel Braided Leader Hose
Intake Filter Assembly
Insulated Wiring with Connectors
30A In-line Fuse with Waterproof Holder
Mounting Hardware Included
Dimensions
7??L x 3-1/4??W x 5-3/4??H
Package Size
Note
The Horn is the perfect addition to 12V vehicles
IMPORTANT
Never attach the compressor to any plastic or other flexible material.
For optimal results, the compressor should be placed as close to the battery as possible. This will reduce the amount of wiring needed.
Avoid placing compressor near flammable liquids.
If you are planning to move compressor?? air intake to an area other than where the compressor was installed, make sure your placement allows for the airline to be routed from the air inlet of the compressor to the remote inlet air filter
Mark the spots for the holes with the mounting base as a guide and then drill. Make sure the compressor is secured.
To enhance performance and make sure the battery of your vehicle doesn?? discharge, keep the engine running while the compressor is being used.
BRAIDED HOSE INSTALLATION
Connect the stainless steel braided hose of the compressor to the tank?? inlet port.
The tank?? inlet port must be 1/4" N.P.T. (National Pipe Thread).
CHECK VALVE
The check valve is an important part of the air compressor and has only one function: to let air flow from one side to the other, in this case from the compressor to the tank, while blocking air flow in the opposite direction.
When installing the braided hose do not rotate or remove the inline check valve located at the end of the hose on the side that connects to the air tank. Doing so will damage its seals and will result in damage to your air compressor.
REMOTE FILTER
Using a compatible remote air filter installation kit (NOT PROVIED) your compressor?? air intake can be installed in an area other than where the compressor was installed.
THERMAL OVERLOAD PROTECTION
The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor.
To prevent the compressor from over running and possible damage due to an air leak, connect the compressor?? red wire to a power source in the vehicle that only gets power when the vehicle?? ignition is on. Recommended connection points are: windshield wiper motor, blower motor or an accessory terminal on the fuse panel.
Make sure to use wire that is as heavy as the wire of the compressor and to use the included fuse for circuit?? protection.
Attach the black wire to any of the Pressure Switch?? connections located on the air tank.
The remaining Pressure Switch connection should be attached to ground. Secure the end to any metal body or to the negative side of the vehicle?? battery. The ground connection should be rust and paint free.
Your compressor is now set for use and will turn on automatically when air pressure in the air tank falls. When air pressure reaches maximum PSI, it will turn off. If the compressor fails to reach the maximum air pressure of the tank, which is the Pressure Switch's cut OFF pressure, check all air connections for leaks. While the compressor is pumping, use soapy water or any bubble solution to perform this check. In case the leak remains after tightening, re-apply thread sealant.
This maintenance free heavy duty Air Compressor is designed for use with any high-pressure Air Horns that require an onboard air system, or many other uses that require air pressure supply. Designed to work with up to 5 gallon air tanks. Simple 2 electric wire installation. This is truly a great quality product you can count on. Ideal for any 12 volt vehicles such as SUVs, Trucks, RVs, Marine and more.
SAFETY INSTRUCTIONS
Do not attempt to disassemble, repair or customize this product.
Avoid setting up any parts of this product where there is a risk of falling off or risk of coming in contact with water.
Avoid reaching out to touch or pick up any fallen or water submerged parts.
Never leave this product unattended during use.
Intended for use by adults only. During and immediately after use, avoid touching any part of the compressor with bare hands as it is very hot during such periods.
Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others.
Avoid use of product near flames, explosive materials, aerosol products or oxygen devices. Be sure to pump nothing other than atmospheric air.
It is important to determine the maximum air pressure for any tool or attachment before using it.
Air sprayer or nozzle should always be pointed away from any part of the body.
The compressor has Thermal Overload Protection, if this protection activates, cut off the source of power and let the unit cool down for about 30 minutes. This will reset the system and allow you to safely resume use of the air compressor.
Make sure your battery ground is detached before you begin. Set the horn up for use only in areas with adequate ventilation.
Employ equipment for eye protection during drilling operations.
Ensure that your air system has no pressure before you begin.
The specific voltage requirement for this horn system is 12 volt DC, therefore installation must be done to a DC power source of 12 volts.